buckitall
Comments
-
Hi, mickeyb44
Did you run the clone process while under Windows?
"If AOMEI Backupper has been employed under the Windows operating system, the system disk can only be set as the source disk, but can not be set as the destination disk…
-
Hi IanCPurdie,
I also cannot find this feature, my guess is that the incremental or differental backups require your 1st backup to be in the same location for reference.
You can move your 1st backup image to a new destination and sch…
-
Hi Plockerman,
Find your "log" files...
C:\program files (86)\aomei backupper (version)\log
and .zip them up and post here please
in The file in an image file can not be mounted or explored Comment by buckitall January 2015
-
-
Hi X4mple,
Are you trying to restore files to a fresh install version of Windows?
Or trying to restore to the formatted disk?
Are you restoring from backups created on a CD, or external HDD?
There should be a…
-
It should not, but as always create a backup for just in case situations that it may fail.
-
Hi Amit,
Try to reboot into pre OS with AOMEI P/A then as YoungCheng suggested, try these solutions...
Solutions:
1. In case of an offline or read-only status disk or volume, the modification of pa…
-
Hi vagn,
You state the backup restores just fine. I'm guessing you are recieving this error due to you using YUMI and the error states "does not match with the current software version" might be due to looking into the wrong location on yo…
-
Hi Gockel,
If you are just looking for an .iso, then I would suggest using AOMEI PE Builder
This will give you the tools to create what you a…
-
I find that sometimes the "system restore" has difficulty finding the boot loader...If you click on "System Restore" and follow up with "No" instead of "Yes" to restoring the system you can just restore the main partition...normally "C:" drive. Y…
-
Hi Shankar,
Open your Disk Management you will be able to see what type of disk you are working with.
To open this click start, click Run then type diskmgmt.msc
From here you should be able to see "disk 1" and under that I'm sur…
-
Sorry about having to re-install,
couldn't you boot up with P/A and changed the letters from there?
-
If your disk shows "RAW" and not formatted then perhaps you can still recover the partitions lost.
Have you tried Partition Assistant in Total identified Windows installations: 0 Comment by buckitall September 2014
-
You mention showing two disks? Does your system have 2 disks installed? If so have you checked you BIOS to confirm which disk to boot up 1st?
-
Hi lordfarquadd,
Great to hear you can at least boot back to XP, How about your other partitions what do they show now?
From what I understand you are trying to format your XP partition and go solely on W8.1? We will try and walk thr…
-
Hi bear2071,
Is your HDD constantly spinning? Is the HDD light flickering all the time? Is this a SSD or HDD? Have you done a malware/virus scan lately?
-
Hi pasigeek,
Your speeds are determined by USB port speed along with external HDD read/write speeds.
Scan the external drive in search for errors
Right-click the drive you want to check, select "Properties"
…
-
Hi jjsilva13,
Sounds like your BCD is corrupt, this can happen sometimes when "splitting" drives causing the O/S to get confused. Have you created a recovery media with your Toshiba software, or Windows Recovery Disc?
Have you tried …
-
Hello diat,
Best practice is to always start with a fresh installation of Windows and build from there your old software.
in Can I still have my old version windows on my new ssd? Comment by buckitall September 2014
-
Hi hellokit,
2TB is a very large disk and could take time to format even if you selected "quick format". If this is an external disk then even longer time. It may seem to be frozen but I would wait at least a couple of hrs.
-
Hi ladyia,
Have you tried to plug the external drive in another system?
Sounds like possibly a driver error with your enclosure, or a disk failure in the near future.
Can you remove the SSD from the enclosure and c…
-
You could give Partition Assistant a try...there is a feature called "Partition Recovery Wizard"
-
Hi raudex,
I use YUMI to create a multiboot usb drive. I would 1st create an .iso boot image of Backupper then use what ever program for your GRUB boot to place that .iso to your USB.
-
Hi ronnieg,
Can you please post a picture of your "disk management"...you can pull this up by
using the run command. Hold down the Windows key and press R, this will give you the run command window where you can enter the command-&g…
-
Hi nopf,
The "I tried to start the file, a Message ( Information only ) appears and then - nothing."
That you mention, I also ran the file downloaded on a Windows 8.1 x64 and here is the pop up that I recieved.
in Combine all AOMEI software into a WinPE tool--AOMEI PE Builder released!!! Comment by buckitall August 2014
-
Hi TimA,
How long did you wait...the process does take a long time to complete and seems like it freezes up.
-
Hi LHnTX,
Sorry to hear your fustration. I am trying to understand a little more about your process. Have you followed the Web-Site on the process of "Clone Disk"?
in Cloned laptop HDD to larger HDD will not boot Comment by buckitall August 2014
-
Hi Scott,
When you describe "pops out", I'm guessing you mean popup while you are moving files?
This might have been installed by the manufacture for your "recovery image" This partition is most likely protected and should be hidden…
-
Hi Helen,
We have to go through several steps to confirm your installation.
1. Physical connection (reconnect cables, make sure they are not loose)
2. BIOS reconize the HDD
3. O/S reconize your partition?
4. Use the…
Your files should be safe.